CM520 install Openwrt with TFTP
星际宝盒 CM520 刷 openwrt
使用串口连接上以后：
root@OpenWrt:/# reboot
root@OpenWrt:/# [ 749.130077] br-lan: port 1(eth0) entered disabled state
[ 749.130737] device eth0 left promiscuous mode
[ 749.134271] br-lan: port 1(eth0) entered disabled state
[ 749.145146] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# [
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00117
S - IMAGE_VARIANT_STRING=DAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000025
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 2611 - bootable_media_detect_success, Start
B - 2625 - elf_loader_entry, Start
B - 4033 - auth_hash_seg_entry, Start
B - 6185 - auth_hash_seg_exit, Start
B - 74246 - elf_segs_hash_verify_entry, Start
B - 198366 - PBL, End
B - 198390 - SBL1, Start
B - 291661 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 293153 - boot_flash_init, Start
D - 92358 - boot_flash_init, Delta
B - 389811 - boot_config_data_table_init, Start
D - 13920 - boot_config_data_table_init, Delta - (419 Bytes)
B - 406487 - clock_init, Start
D - 7571 - clock_init, Delta
B - 417499 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 420912 - sbl1_ddr_set_params, Start
B - 426006 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 430387 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13170 - sbl1_ddr_set_params, Delta
B - 443697 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 514718 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 530812 - Image Load, Start
D - 146098 - QSEE Image Loaded, Delta - (274048 Bytes)
B - 677337 - Image Load, Start
D - 2118 - SEC Image Loaded, Delta - (2048 Bytes)
B - 687512 - Image Load, Start
D - 181223 - APPSBL Image Loaded, Delta - (428763 Bytes)
B - 869130 - QSEE Execution, Start
D - 56 - QSEE Execution, Delta
B - 875347 - SBL1, End
D - 679067 - SBL1, Delta
S - Flash Throughput, 2040 KB/s (705630 Bytes, 345879 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Mar 20 2018 - 09:22:26)
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010001
NAND: ID = 9580f12c
Vendor = 2c
Device = f1
ONFI device found
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC: qca_mmc: 0
In: serial
Out: serial
Err: serial
machid: 8010001
flash_type: 2
Hit any key to stop autoboot: 0
Net: MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
(IPQ40xx) #
(IPQ40xx) #
(IPQ40xx) # printenv
baudrate=115200
bootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
bootcmd=bootipq
bootdelay=2
ethact=eth0
fdt_high=0x87000000
fileaddr=88000000
filesize=5C7DF
flash_type=2
fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
ipaddr=192.168.1.183
machid=8010001
mtddevname=fs
mtddevnum=0
mtdids=nand0=nand0
mtdparts=mtdparts=nand0:0x4100000@0xb80000(fs),
partition=nand0,0
serverip=192.168.1.188
stderr=serial
stdin=serial
stdout=serial
Environment size: 515/262140 bytes
(IPQ40xx) # tftpboot xinjiyun-ttl-shuaji-openwrt-ipq40xx-jikeap_cm520-squashfs-nand-factory.ubi
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 up Speed :1000 Full duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
TFTP from server 192.168.1.188; our IP address is 192.168.1.183
Filename 'xinjiyun-ttl-shuaji-openwrt-ipq40xx-jikeap_cm520-squashfs-nand-factory.ubi'.
Load address: 0x84000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########
done
Bytes transferred = 19005440 (1220000 hex)
(IPQ40xx) # nand erase 0x4c80000 0x3300000
NAND erase: device 0 offset 0x4c80000, size 0x3300000
Erasing at 0x7f60000 -- 100% complete.
OK
(IPQ40xx) # nand write 0x84000000 0x4c80000
NAND write: device 0 offset 0x4c80000, size 0x3380000
54001664 bytes written: OK
(IPQ40xx) # reset
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00117
S - IMAGE_VARIANT_STRING=DAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000025
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 2611 - bootable_media_detect_success, Start
B - 2625 - elf_loader_entry, Start
B - 4033 - auth_hash_seg_entry, Start
B - 6184 - auth_hash_seg_exit, Start
B - 74252 - elf_segs_hash_verify_entry, Start
B - 198202 - PBL, End
B - 198226 - SBL1, Start
B - 291501 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 292993 - boot_flash_init, Start
D - 92368 - boot_flash_init, Delta
B - 389665 - boot_config_data_table_init, Start
D - 13919 - boot_config_data_table_init, Delta - (419 Bytes)
B - 406337 - clock_init, Start
D - 7571 - clock_init, Delta
B - 417347 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 420760 - sbl1_ddr_set_params, Start
B - 425855 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 430236 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13170 - sbl1_ddr_set_params, Delta
B - 443546 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 514593 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 530901 - Image Load, Start
D - 146257 - QSEE Image Loaded, Delta - (274048 Bytes)
B - 677587 - Image Load, Start
D - 2119 - SEC Image Loaded, Delta - (2048 Bytes)
B - 687765 - Image Load, Start
D - 181490 - APPSBL Image Loaded, Delta - (428763 Bytes)
B - 869651 - QSEE Execution, Start
D - 56 - QSEE Execution, Delta
B - 875870 - SBL1, End
D - 679755 - SBL1, Delta
S - Flash Throughput, 2037 KB/s (705630 Bytes, 346303 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Mar 20 2018 - 09:22:26)
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010001
NAND: ID = 9580f12c
Vendor = 2c
Device = f1
ONFI device found
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC: qca_mmc: 0
In: serial
Out: serial
Err: serial
machid: 8010001
flash_type: 2
Hit any key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000b80000-0x000004c80000 : "mtd=0"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 65 MiB
UBI: number of good PEBs: 520
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 3
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 520
UBI: number of PEBs reserved for bad PEB handling: 5
UBI: max/mean erase counter: 48/19
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (3174400)
## Booting kernel from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.14.95
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 3051362 Bytes = 2.9 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: cb9917c3
Hash algo: sha1
Hash value: c54c359a2b48a45a771c0f8be292778dcc89d63b
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt jikeap_cm520 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x842e9180
Data Size: 16655 Bytes = 16.3 KiB
Architecture: ARM
Hash algo: crc32
Hash value: a942efec
Hash algo: sha1
Hash value: 05c9d7fafc0057c4ed03b3f7a17ba0ca36e0ab36
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x842e9180
Uncompressing Kernel Image ... OK
Loading Device Tree to 86ff8000, end 86fff10e ... OK
Device nand2 not found!
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.95 (li@ubuntu) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7676-cddd7b4c77)) #0 SMP Wed Jan 30 12:21:02 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: JikeAP CM520
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c0 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @dfbaf000 s29324 r8192 d23924 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129536
[ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwaitubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 509840K/522240K available (4396K kernel code, 141K rwdata, 1228K rodata, 1024K init, 230K bss, 12400K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc074b1a8 (5389 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a23640 ( 142 kB)
[ 0.000000] .bss : 0xc0a25000 - 0xc0a5e898 ( 231 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000021] Switching to timer-based delay loop, resolution 20ns
[ 0.000247] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000268] pid_max: default: 32768 minimum: 301
[ 0.000408] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000959] CPU: Testing write buffer coherency: ok
[ 0.001648] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.001788] Hierarchical SRCU implementation.
[ 0.002428] smp: Bringing up secondary CPUs ...
[ 0.005097] smp: Brought up 1 node, 4 CPUs
[ 0.005115] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.005124] CPU: All CPU(s) started in SVC mode.
[ 0.009293] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.009442] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.009465] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.009643] pinctrl core: initialized pinctrl subsystem
[ 0.010589] NET: Registered protocol family 16
[ 0.010957] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.012012] cpuidle: using governor ladder
[ 0.012058] cpuidle: using governor menu
[ 0.029055] msm_bus_fabric_init_driver
[ 0.029753] usbcore: registered new interface driver usbfs
[ 0.029812] usbcore: registered new interface driver hub
[ 0.029902] usbcore: registered new device driver usb
[ 0.029949] pps_core: LinuxPPS API ver. 1 registered
[ 0.029961] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.030059] PTP clock support registered
[ 0.031165] clocksource: Switched to clocksource arch_sys_counter
[ 0.031959] NET: Registered protocol family 2
[ 0.032593] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.032660] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.032751] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.032857] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.032894] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.033095] NET: Registered protocol family 1
[ 0.034182] No memory allocated for crashlog
[ 0.034379] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.037526] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.037541] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.042652] io scheduler noop registered
[ 0.042671] io scheduler deadline registered (default)
[ 0.044694] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
[ 0.044713] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
[ 0.045938] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.046018] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.046100] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.046172] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.046395] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.046925] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.046983] msm_serial 78af000.serial: uartclk = 1843200
[ 0.047032] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 24, base_baud = 115200) is a MSM
[ 0.047059] msm_serial: console setup on port #0
[ 0.571648] console [ttyMSM0] enabled
[ 0.576541] msm_serial: driver initialized
[ 0.583978] loop: module loaded
[ 0.585467] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1
[ 0.586900] nand: Micron MT29F1G08ABAEAWP
[ 0.593538] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.597492] 14 fixed-partitions partitions found on MTD device qcom_nand.0
[ 0.604888] Creating 14 MTD partitions on "qcom_nand.0":
[ 0.611751] 0x000000000000-0x000000100000 : "0:SBL1"
[ 0.618656] 0x000000100000-0x000000200000 : "0:MIBIB"
[ 0.623547] 0x000000200000-0x000000300000 : "0:BOOTCONFIG"
[ 0.628427] 0x000000400000-0x000000500000 : "0:QSEE"
[ 0.633855] 0x000000300000-0x000000400000 : "0:QSEE_1 "
[ 0.638947] 0x000000580000-0x000000600000 : "0:CDT"
[ 0.643576] 0x000000500000-0x000000580000 : "0:CDT_1"
[ 0.648334] 0x000000600000-0x000000680000 : "0:BOOTCONFIG1"
[ 0.653626] 0x000000680000-0x000000700000 : "0:APPSBLENV"
[ 0.658921] 0x000000900000-0x000000b00000 : "0:APPSBL"
[ 0.665736] 0x000000700000-0x000000900000 : "0:APPSBL_1"
[ 0.670710] 0x000000b00000-0x000000b80000 : "0:ART"
[ 0.675055] 0x000004c80000-0x000007f80000 : "rootfs"
[ 0.681940] random: fast init done
[ 0.721378] mtd: device 12 (rootfs) set to be root filesystem
[ 0.721678] mtdsplit: no squashfs found in "rootfs"
[ 0.726120] 0x000000b80000-0x000004c80000 : "rootfs_1"
[ 0.791317] libphy: ipq40xx_mdio: probed
[ 0.822090] ESS reset ok!
[ 0.855071] ESS reset ok!
[ 0.925395] PHY 0 single test PSGMII issue happen!
[ 1.250592] PHY0 test see issue!
[ 1.290757] ESS reset ok!
[ 1.721579] libphy: Fixed MDIO Bus: probed
[ 1.722466] EDMA using MAC@ - using
[ 1.722484] ae:84:8d:46:e5:df
[ 1.730800] i2c /dev entries driver
[ 1.732962] sdhci: Secure Digital Host Controller Interface driver
[ 1.734376] sdhci: Copyright(c) Pierre Ossman
[ 1.740623] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.764071] NET: Registered protocol family 10
[ 1.765628] Segment Routing with IPv6
[ 1.767516] NET: Registered protocol family 17
[ 1.771633] 8021q: 802.1Q VLAN Support v1.8
[ 1.775707] Registering SWP/SWPB emulation handler
[ 1.784848] ubi0: attaching mtd12
[ 2.000118] ubi0: scanning is finished
[ 2.018757] ubi0: volume 2 ("rootfs_data") re-sized from 9 to 241 LEBs
[ 2.019337] ubi0: attached mtd12 (name "rootfs", size 51 MiB)
[ 2.024229] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.029996] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.036785] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.043639] ubi0: good PEBs: 408, bad PEBs: 0, corrupted PEBs: 0
[ 2.050392] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.056664] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1215869843
[ 2.063699] ubi0: available PEBs: 0, total reserved PEBs: 408, PEBs reserved for bad PEB handling: 20
[ 2.072997] ubi0: background thread "ubi_bgt0d" started, PID 85
[ 2.073024] ubi: mtd12 is already attached to ubi0
[ 2.087804] UBI error: cannot attach mtd12
ɛ 2.117243] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.119666] Freeing unused kernel memory: 1024K
[ 2.530218] init: Console is alive
[ 2.530453] init: - watchdog -
[ 3.646248] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.661197] random: crng init done
[ 3.685901] exFAT: Version 1.2.9
[ 3.700149] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.704349] SCSI subsystem initialized
[ 3.708045] ehci-platform: EHCI generic platform driver
[ 3.710872] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.716188] ohci-platform: OHCI generic platform driver
[ 3.722044] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.141719] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.142325] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.148293] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010
[ 4.154966] xhci-hcd xhci-hcd.0.auto: irq 93, io mem 0x08a00000
[ 4.171443] hub 1-0:1.0: USB hub found
[ 4.172147] hub 1-0:1.0: 1 port detected
[ 4.175262] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.178297] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.183618] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 4.191279] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.198249] hub 2-0:1.0: USB hub found
[ 4.206145] hub 2-0:1.0: 1 port detected
[ 4.321933] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.322504] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.328328] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010
[ 4.335130] xhci-hcd xhci-hcd.1.auto: irq 94, io mem 0x06000000
[ 4.344181] hub 3-0:1.0: USB hub found
[ 4.349326] hub 3-0:1.0: 1 port detected
[ 4.353527] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.357187] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 4.362524] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.370167] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.377339] hub 4-0:1.0: USB hub found
[ 4.385105] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 4.392132] usbcore: registered new interface driver usb-storage
[ 4.395947] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.421460] init: - preinit -
[ 5.884499] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.884657] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 5.889462] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.881745] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.069132] mount_root: loading kmods from internal overlay
[ 9.089837] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 9.094242] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.536621] UBIFS (ubi0:2): default file-system created
[ 9.537368] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 180
[ 9.588553] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 9.588594] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.595422] UBIFS (ubi0:2): FS size: 29331456 bytes (27 MiB, 231 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
[ 9.605325] UBIFS (ubi0:2): reserved for root: 1385396 bytes (1352 KiB)
[ 9.615532] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID CAC31558-43FC-4C9A-AA32-AAA1116BA83A, small LPT model
[ 9.622858] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 9.633727] block: unable to load configuration (fstab: Entry not found)
[ 9.640396] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 9.647409] block: unable to load configuration (fstab: Entry not found)
[ 9.653699] block: attempting to load /etc/config/fstab
[ 9.663635] block: unable to load configuration (fstab: Entry not found)
[ 9.665388] block: no usable configuration
[ 9.742034] UBIFS (ubi0:2): un-mount UBI device 0
[ 9.742523] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 9.754443] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 181
[ 9.805750] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 9.805791] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.812599] UBIFS (ubi0:2): FS size: 29331456 bytes (27 MiB, 231 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
[ 9.822501] UBIFS (ubi0:2): reserved for root: 1385396 bytes (1352 KiB)
[ 9.832728] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID CAC31558-43FC-4C9A-AA32-AAA1116BA83A, small LPT model
[ 10.085526] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 10.085661] block: unable to load configuration (fstab: Entry not found)
[ 10.091485] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 10.098354] block: unable to load configuration (fstab: Entry not found)
[ 10.104689] block: attempting to load /etc/config/fstab
[ 10.111500] block: unable to load configuration (fstab: Entry not found)
[ 10.116344] block: no usable configuration
[ 10.181952] mount_root: overlay filesystem has not been fully initialized yet
[ 10.182684] mount_root: switching to ubifs overlay
[ 10.220326] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.376601] procd: - early -
[ 10.376741] procd: - watchdog -
[ 11.091310] procd: - watchdog -
[ 11.091629] procd: - ubus -
[ 11.312990] procd: - init -
Please press Enter to activate this console.
[ 11.805840] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.819238] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 11.824817] tun: Universal TUN/TAP device driver, 1.6
[ 11.829955] gre: GRE over IPv4 demultiplexor driver
[ 11.831282] ip_gre: GRE over IPv4 tunneling driver
[ 11.838934] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.845465] Netfilter messages via NETLINK v0.30.
[ 11.847256] ip_set: protocol 6
[ 11.877477] u32 classifier
[ 11.877504] input device check on
[ 11.879074] Actions configured
[ 11.884819] Mirror/redirect action on
[ 11.893790] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 11.898510] fuse init (API version 7.26)
[ 11.902749] usbcore: registered new interface driver cdc_wdm
[ 11.903892] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 11.908419] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 11.918857] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.928550] ctnetlink v0.93: registering with nfnetlink.
[ 11.973925] usbcore: registered new interface driver usbserial
[ 11.974028] usbcore: registered new interface driver usbserial_generic
[ 11.978779] usbserial: USB Serial support registered for generic
[ 12.022415] xt_time: kernel timezone is -0000
[ 12.024332] usbcore: registered new interface driver cdc_ether
[ 12.077279] PPP generic driver version 2.4.2
[ 12.078450] PPP MPPE Compression module registered
[ 12.081955] NET: Registered protocol family 24
[ 12.086889] usbcore: registered new interface driver qmi_wwan
[ 12.283199] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2
[ 12.283281] ath10k_ahb a000000.wifi: Falling back to user helper
[ 17.325425] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 17.325482] ath10k_ahb a000000.wifi: Falling back to user helper
[ 17.381761] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 17.633445] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 17.633495] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 17.646585] ath10k_ahb a000000.wifi: firmware ver 10.4-3.5.3-00057 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6a15d64d
[ 17.706739] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 83549421
[ 19.104194] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 19.303172] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2
[ 19.303225] ath10k_ahb a800000.wifi: Falling back to user helper
[ 19.699847] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 19.699893] ath10k_ahb a800000.wifi: Falling back to user helper
[ 19.770471] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 19.770768] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 19.778443] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 19.792531] ath10k_ahb a800000.wifi: firmware ver 10.4-3.5.3-00057 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6a15d64d
[ 19.838698] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 83549421
[ 21.239882] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 21.263013] usbcore: registered new interface driver option
[ 21.263141] usbserial: USB Serial support registered for GSM modem (1-port)
[ 21.272019] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 31.678268] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 31.685104] br-lan: port 1(eth0.1) entered blocking state
[ 31.685146] br-lan: port 1(eth0.1) entered disabled state
[ 31.689826] device eth0.1 entered promiscuous mode
[ 31.694992] device eth0 entered promiscuous mode
[ 31.702759] br-lan: port 1(eth0.1) entered blocking state
[ 31.704354] br-lan: port 1(eth0.1) entered forwarding state
[ 31.709838] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 32.721273] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.721963] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 35.942907] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 37.585674] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 37.590572] br-lan: port 2(wlan0) entered blocking state
[ 37.590618] br-lan: port 2(wlan0) entered disabled state
[ 37.596418] device wlan0 entered promiscuous mode
[ 37.605045] br-lan: port 3(wlan1) entered blocking state
[ 37.605868] br-lan: port 3(wlan1) entered disabled state
[ 37.611755] device wlan1 entered promiscuous mode
[ 38.133681] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 38.133945] br-lan: port 3(wlan1) entered blocking state
[ 38.139121] br-lan: port 3(wlan1) entered forwarding state
[ 39.553514] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 39.553731] br-lan: port 2(wlan0) entered blocking state
[ 39.558961] br-lan: port 2(wlan0) entered forwarding state
最后修改于 Mon, 30 Sep 2019